I picked up a G2 throttle cam system to with my new Rizoma sport bend MA010 handlebars. Just curious what cam is best to run on the SD? The 100 cam is same as stock, 200 is a little more forgiving, and 400 is most forgiving. The adventure guys seem to be running 400 cam mostly, is that too much slack for the SD? I think I'll try the 200 first, but I figured someone here probably knows what is best by now.
G2 Throttle cam system
20 posts · Started by Willh · 27 Sep 2012
Post 2 by Mr_Trecolareco,
#2If your injection is sorted than 100 or the 50, if not start with 200 ...
Post 3 by Colonel_Klinck,
#3Post missing
This post could not be recovered from the original forum.
Post 4 by Mr_Trecolareco,
#4If your injection is sorted .25 Fooking love that cam! I think its a good idea to leave a small amount of slack in the throttle cables though. The slightest twitch at lower speeds can result in a input if you are not careful.
Post 5 by fuel,
#5I've got the O2 sensor eliminators installed and akra pipes with map. The throttle still has a little snatch to it, nothing terrible. What else can I do besides SAS block off?
Post 6 by 41KS,
#6Post missing
This post could not be recovered from the original forum.
Post 7 by 990 WFO,
#7With Craig on this one .25 is awesome
Post 8 by MADDOG53,
#8Post missing
This post could not be recovered from the original forum.
Post 9 by CEREC1,
#9Post missing
This post could not be recovered from the original forum.
Post 10 by jambox,
#10I'm running the .25 and its awesome. I've got a pretty smooth tune, no O2 sensors, and no SAS though. With the .25 its a bit snatchy but still not as bad as when the bike was 100% stock. Now I no longer have to break my wrist trying to go full throttle.
Post 11 by MADDOG53,
#11Snatchy throttle on my bike when new was down right awful,,,installed the G2 with the .50 cam,,,AKRA download with Yoshi's,,02 eliminators,,have not done the SAS as of yet,,,,,smoothed out the throttle so much it seemed to be a different bike,,I would think when I install my motobox and remove the SAS thing's will smoothe out further,,,at which point I will be doing tune ECU to make the whole package that much more rideable on the street,,,,
Post 12 by omky756,
#12So guys where is the best place to get this throttle cam To date advice seems to be to buy from a dealer in Denmark if we are UK based.
Any advice on an easier way to fit than seemingly have to do lots of grinding of the throttle housing.
Any advice on an easier way to fit than seemingly have to do lots of grinding of the throttle housing.
Post 13 by CEREC1,
#13Post missing
This post could not be recovered from the original forum.
Post 14 by Colonel_Klinck,
#14I purchase mine here,,,,ship's international,,,,,,,,,,,,
http://www.ktmtwins.com/ktm-990-super-d ... tegory=480
http://www.ktmtwins.com/ktm-990-super-d ... tegory=480
Post 15 by Viking,
#15Post missing
This post could not be recovered from the original forum.
Post 16 by nampus,
#16Post missing
This post could not be recovered from the original forum.
Post 17 by Colonel_Klinck,
#17Just needs a bit of dremel work. Can't see KTM releasing a cam that is as fast action as the .25
Post 18 by omky756,
#18Post missing
This post could not be recovered from the original forum.
Post 19 by nampus,
#19Post missing
This post could not be recovered from the original forum.
Post 20 by Colonel_Klinck,
#20Post missing
This post could not be recovered from the original forum.
End of archived topic · Posting is closedBack to top ↑
← Back to Technical - Dr F's Words of Wisdom